BELSHAW PLUNGERS, CYLINDERS AND ATTACHMENTS FOR TYPE B/F/N DEPOS

Plungers, Cylinders and Attachments for Type B/F/N Depositors... Belshaw plungers are high-quality stainless steel manufactured to very close tolerances. Sizes are in 1/8" increments through the range shown in the table below. Size is obtained by measuring the diameter of the base of the plunger. Cylinders : Cylinders (see example at below) are inserted into the base of the hopper. Every plunger must match a similar size cylinder. More than one plunger can be used with the same cylinder, provided all are the same size. Depositor Types Plungers, cylinders and attachments are identical for Type B and Type F. Type N plungers are similar but shorter, and NOT interchangeable with Type B/F. Plunger selection guide Both Type B/F and Type N plunger part numbers are listed below. Other plungers and a wider range of sizes can be made as "specials" (contact your distributor). For Old Fashion donuts, use a plain plunger. Download Specs Plain Plunger Star Plunger French Cake (std mix) or French Cruller (cruller mix) Type B/F Plungers Part No: 7SS Range: 1-1/2" to 2" Part No: 7SC-SS Range: 1" to 2" Part No: 7B-1009 Range: 1-1/2" to 2" Type N Plungers Part No: N-1007SS Range: 1-1/2" to 2" Part No: N-1007SSS Range: 1-1/2" to 2" Part No: N-1008SS Range: 1-1/2" to 2" Download Specs Krinkle plunger Ball plunger (specify 1,2,3,4 or 5 holes) Stick plunger (1 or 2 slots) Type B/F Plungers Part No: 7F-1004 Range: 1-1/2" to 2" Part No: 7G-1000 Range: 1-1/2" to 2" 7H-1000 (1 slot) 7H-1001 (2 slots) Range: 1-1/2" to 2" Type N Plungers Part No: N-1012SS Range: 1-1/2" to 2" Part No: N-1009BSS Range: 1-1/2" to 2" Part No: N-1009SS Range: 1-1/2" to 2" Cylinder Selection Cylinders are inserted into the base of your Belshaw hopper. The plunger passes through the heavy duty, precision-manufactured cylinder liner with a minimum of clearance to form cake donuts. After depositing many thousands of donuts, friction gradually wears out the sleeve on the interior, to the point where you need a new cylinder. For all Belshaw depositors: Each plunger you use must match a cylinder of the exact same size. For instance, you cannot use a 1-1/2" plunger with a 1-3/4" cylinder. Several plungers may be used with one cylinder, provided all are the same size. Cylinder - for Type B and F A 1-3/4" plain plunger and cylinder is standard with Type B and Type F depositor. Type B and F cylinders are interchangeable, and any size will fit any Type B and Type F depositor. When ordering cylinders, specify both part number and size. 35SSA - small bore, for plungers 1" to 1-3/4" 35SSB - large bore, for plungers 1-7/8", 2" Cylinder - for Type N, large cylinder with with small bore If you are ordering a replacement cylinder, compare the dimensions of your old cylinder to the diagram at left. Notice that although this cylinder has a slot, it does NOT penetrate to the steel liner on the inside. Part Number N-1035L-A for plungers 7/8", 1", 1-1/8", 1-1/4", 1-3/8", 1-1/2", 1-5/8", 1-3/4" Cylinder - for Type N, large cylinder with with large bore If you are ordering a replacement cylinder, compare the dimensions of your old cylinder to the diagram at left. Notice that this cylinder has a slot that penetrates to the steel liner on the inside. Part Number N-1035L-B for plungers 1-7/8", 2", 2-1/8", 2-1/4" only Cylinder - for Type N, small cylinder with small bore, OBSOLETE If you are ordering a replacement cylinder, compare the dimensions of your old cylinder to the diagram at left. Notice that this cylinder has a slot that penetrates to the steel liner on the inside. Part Number N-1035 - for plungers up to 1-3/4" Belshaw plungers are high-quality stainless steel manufactured to very close tolerances. Sizes are in 1/8" increments through the range shown in the table below. Size is obtained by measuring the diameter of the base of the plunger.Cylinders:Cylinders (see example at below) are inserted into the base of the hopper. Every plunger must match a similar size cylinder. More than one plunger can be used with the same cylinder, provided all are the same size. Depositor TypesPlungers, cylinders and attachments are identical for Type B and Type F. Type N plungers are similar but shorter, and NOT interchangeable with Type B/F.Plunger selection guideBoth Type B/F and Type N plunger part numbers are listed below. Other plungers and a wider range of sizes can be made as "specials" (contact your distributor). For Old Fashion donuts, use a plain plunger. Download Specs Type B/F Plungers Cylinder SelectionCylinders are inserted into the base of your Belshaw hopper. The plunger passes through the heavy duty,precision-manufactured cylinder liner with a minimum of clearance to form cake donuts. After depositingmany thousands of donuts, friction gradually wears out the sleeve on the interior, to the point where you need a new cylinder.For all Belshaw depositors:Each plunger you use must match a cylinder of the exact same size. For instance, you cannot use a 1-1/2" plunger with a 1-3/4" cylinder.Several plungers may be used with one cylinder, provided all are the same size.